参考设计
(15)
Single Cell Battery Power Solution Reference Design
PMP5722: This reference design shows the functionality and performance of a complete single-cell battery power solution using a coin-cell Li-Ion battery. It can be powered either by an external adapter or by an USB port. When the board is connected to a computer, the load current, state-of-charge, and much more information about the battery can be monitored on a GUI.
TIDA-00296 Automotive Body Control Module Driver Reference Design | TI.com
TIDA-00296: TIDA-00296 is a reference design that highlights TI's high-side and low-side relay, motor, and load driver portfolios. The loads for this design (door locks, window lifts, seat heaters, HVAC, lamps, and LEDs) were chosen to show the range of loads that a BCM can drive and how TI's solutions fit into these areas.
Automotive Body Control Module Driver Reference Design
TIDA-00296: TIDA-00296 is a reference design that highlights TI's high-side and low-side relay, motor, and load driver portfolios. The loads for this design (door locks, window lifts, seat heaters, HVAC, lamps, and LEDs) were chosen to show the range of loads that a BCM can drive and how TI's solutions fit into these areas.
Reference Design for an Interface to a Position Encoder with EnDat 2.2
TIDA-00172: This TI Design implements a hardware interface solution based on the HEIDENHAIN EnDat 2.2 standard for position or rotary encoders. The building blocks include the power supply for the encoder – with innovative smart e-Fuse technology - and robust half-duplex RS485 transceivers, including line termination and EMC protection. An auxiliary power supply and logic level interface with adjustable I/O voltage level is provided to connect to subsequent MCUs and MPUs that would run the EnDat 2.2 Master protocol stack. This design is fully tested to meet EMC immunity requirements for ESD, Fast Transient Burst and Surge according to IEC61800-3.
TIDA-00175 Interface to a 5V BiSS Position Encoder Reference Design | TI.com
TIDA-00175: This TI Design implements a hardware interface solution based on the BiSS standard for position or rotary encoders. It supports both BiSS Point-to-Point and BiSS Bus configurations.The building blocks include the power supply for a 5V BiSS encoder – with innovative smart e-Fuse technology - and robust full-duplex RS485 transceivers, including line termination and EMC protection. An auxiliary power supply and logic level interface with adjustable I/O voltage level is provided to connect to subsequent MCUs and MPUs that would run the BiSS (or SSI) Master protocol stack. This design is fully tested to meet EMC immunity requirements for ESD, Fast Transient Burst and Surge according to IEC61800-3.
Interface to a 5V BiSS Position Encoder Reference Design
TIDA-00175: This TI Design implements a hardware interface solution based on the BiSS standard for position or rotary encoders. It supports both BiSS Point-to-Point and BiSS Bus configurations.The building blocks include the power supply for a 5V BiSS encoder – with innovative smart e-Fuse technology - and robust full-duplex RS485 transceivers, including line termination and EMC protection. An auxiliary power supply and logic level interface with adjustable I/O voltage level is provided to connect to subsequent MCUs and MPUs that would run the BiSS (or SSI) Master protocol stack. This design is fully tested to meet EMC immunity requirements for ESD, Fast Transient Burst and Surge according to IEC61800-3.
TIDA-01226 Compact Full HD 1080p (up to 16 Amps) Projection Display Reference Design Using DLP Pico Technology | TI.com
TIDA-01226: This reference design, featuring the DLP Pico™ 0.47-inch TRP Full-HD 1080p display chipset and implemented in the DLP LightCrafter Display 4710 G2 evaluation module (EVM), enables use of full HD resolution for projection display applications such as accessory projectors, screenless displays, interactive displays, wearables (including head mounted displays), signage, industrial and medical displays. The chipset used in the design is comprised of the DLP4710 (.47 1080p) DMD, the DLPC3439 display controller and the DLPA3005 PMIC/LED driver.
TIDA-00172 Reference Design for an Interface to a Position Encoder with EnDat 2.2 | TI.com
TIDA-00172: This TI Design implements a hardware interface solution based on the HEIDENHAIN EnDat 2.2 standard for position or rotary encoders. The building blocks include the power supply for the encoder – with innovative smart e-Fuse technology - and robust half-duplex RS485 transceivers, including line termination and EMC protection. An auxiliary power supply and logic level interface with adjustable I/O voltage level is provided to connect to subsequent MCUs and MPUs that would run the EnDat 2.2 Master protocol stack. This design is fully tested to meet EMC immunity requirements for ESD, Fast Transient Burst and Surge according to IEC61800-3.
TIDA-00201 Differential Signal Conditioning Circuit for Current and Voltage Measurement Using Fluxgate Sensors | TI.com
TIDA-00201: This design provides a 4-channel signal conditioning solution for differential ADCs integrated into a microcontroller measuring motor current using fluxgate sensors. Also provided is an alternative measurement circuit with external differential SAR ADCs as well as circuits for high-speed overcurrent and earth fault detection. Proper differential signal conditioning improves noise immunity on critical current measurements in motor drives. This reference design can help increase the effective resolution of the analog-to-digital conversion, improving motor drive efficiency.
Differential Signal Conditioning Circuit for Current and Voltage Measurement Using Fluxgate Sensors
TIDA-00201: This design provides a 4-channel signal conditioning solution for differential ADCs integrated into a microcontroller measuring motor current using fluxgate sensors. Also provided is an alternative measurement circuit with external differential SAR ADCs as well as circuits for high-speed overcurrent and earth fault detection. Proper differential signal conditioning improves noise immunity on critical current measurements in motor drives. This reference design can help increase the effective resolution of the analog-to-digital conversion, improving motor drive efficiency.
PMP5722 Single Cell Battery Power Solution Reference Design | TI.com
PMP5722: This reference design shows the functionality and performance of a complete single-cell battery power solution using a coin-cell Li-Ion battery. It can be powered either by an external adapter or by an USB port. When the board is connected to a computer, the load current, state-of-charge, and much more information about the battery can be monitored on a GUI.
