参考设计
(16)
8V @ 7A Synchronous Boost Reference Design with LM5121
PMP10092: The PMP10092 reference design is a synchronous boost converter that can operate over a 3V to 8V input range and produce an 8V output at 7A load. The circuit has an output disconnection switch for safety. Due to the synchronous design a high efficiency of 97% can be achieved.
192W Dual-Phase Synchronous Boost Converter Reference Design
PMP9403: PMP9403 is a high-efficiency dual-phase synchronous boost converter using the LM5122 controller ICs. The design accepts an input voltage of 9Vin to 15Vin (12Vin Nominal) and provides an output of 48Vout capable of supplying 4A of continuous current to the load.
16.8V/18A 4 Switch Buck Boost Reference Design
PMP10214: The PMP10214 reference design has a wide input voltage range from 8 -16V DC with a surge capapbility to 40V. The topology is 4 switch buck boost. It is best suited for charging 4s Li-Ion starter batteries (4 cells).
20W SEPIC Low-Cost Lead Acid Battery Charger Reference Design
PMP10081: The PMP10081 reference design shows a simple and low-cost solution of a lead acid battery charger. The input voltage range is from 9V to 36V and the maximum output voltage is 13.8V, which is sufficient for a six-cell lead acid battery with a charge current up to 1.5A.
18V-36Vdc Input, 5V/30W Active Clamp Forward - Reference Design
PMP4468: The PMP4468 is a DC-DC isolated module reference design targeted for industrial and telecom applications. The DC input range is 18V-36V, with 24V typical and the output is 5V/6A. An active clamp forward controller LM5025A is used in the design. The efficiency is up to 90% with good thermal performance.
The best compatability with E-Transfomer for 5W MR16 application
PMP8008: This demonstration board is desinged for 5W / 3 LEDs MR16 application. The board is favorable for difference supply source, DC power supply (12VDC), AC Magnet Transfomer (12VAC with 50/60Hz) & E-transfromer (12VAC). Also, It has very good E-transfomer compatability and higher efficiency.
150W Boost Converter with LM5121 Reference Design
PMP8673: The PMP8673 reference design is a synchronous boost converter optimized for high efficiency while maintaining a small form factor. This reference design has a voltage input range of 34.5-37.5V (35V nominal) and provides an output voltage of 55.5V. The synchronous boost topology enables efficiencies greater than 97% in the 2-3A load range. The switching frequency is set for 400Khz allowing the use of smaller external components and a total board area of less than 60 square centimeters.
120Vac Single Stage Non-Dimmable 50W LED Driver Reference Design
PMP6017: This reference design provides a high power ( 50W ) non-isolated, non-dimming LED driver based on the TPS92074. With a nominal input of 120VAC and input range covering 108VAC to 132VAC, the design provides 1 Amp of output current to a 47V nominal stack of LEDs (~16 LEDs). The Buck PFC provides high power factor and low THD.
100-240VAC Input, 60W, 2-string, PWM Dimmable LED Driver Reference Design
PMP6024: PMP6024 is an offline, LED driver circuit consisting of an isolated, power-factor corrected, constant output voltage flyback converter followed by two DC/DC buck LED current controllers. It is suitable for indoor or outdoor area lighting applications of 3500-5000 lumens (depending upon LED selection). LED brightness is controlled by a 3.3V, 10kHz PWM signal which is converted to a DC level adjustment of the LED string currents avoiding PWM modulation of the light output.
