参考设计
(30)
System Level Power Reference Design for A13 Automotive Wireless Charger Transmitter
PMP10709: PMP10709 is a system optimized 50 W power designs for A13 Wireless Charger Transmitter used in automotive system. The design has various front end automotive protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Through PFET’s body diode), Battery Disconnect Switch with OVP protection (PFET). PMP10709 is primarily four Switch synchronous Buck – Boost design, which supports wide Input voltage range (7V-20V) and delivers any output from 1V-10V based on DAC output of the A13 Wireless Charger. The DAC output changes from 1V to 3.3V which in turn changes the output voltage from 10V to 1V (on the fly) as needed by the algorithm of A13 wireless charger’s transmitter. This design utilizes best in Class Synchronous four Switch Buck Boost Controller LM5175. The design accepts an input voltage of 7Vin to 20Vin and provides the output of 1V- 10V@5 A. Output current never exceeds 5A to protect the charging Coil. The average current regulation loop of the IC at the output is used for this protection.
PMP20322 24W 12Vout for Flash Power in Enterprise SSD Reference Design | TI.com
PMP20322: PMP20322 is a 4-switch buck-boost controller utilizing the LM5175 for consumer applications. This design has a minimum operating input voltage of 10V and a maximum input voltage of 14V. The design is capable of sourcing 2A continuous current at 12Vout. Switching frequency is set to 300kHz. PMP20322 is assembled on PMP20107 PCB.
220W Synchronous 4 Switch Buck-Boost Converter
PMP9490: PMP9490 is a 225W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts an input voltage of 9.5Vin to 20Vin and provides the outputs of 15V@15 A for Constant Voltage Output Application such as Voltage stabilizer or as Power amplifier SMPS, 10.8V to 15V@12.5A for CC/CV Battery Charger application, and 12.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters. The average current regulation loop of the IC at the output is used for Battery Charging profiling with no external circuit being involved.
PMP10709 System Level Power Reference Design for A13 Automotive Wireless Charger Transmitter | TI.com
PMP10709: PMP10709 is a system optimized 50 W power designs for A13 Wireless Charger Transmitter used in automotive system. The design has various front end automotive protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Through PFET’s body diode), Battery Disconnect Switch with OVP protection (PFET). PMP10709 is primarily four Switch synchronous Buck – Boost design, which supports wide Input voltage range (7V-20V) and delivers any output from 1V-10V based on DAC output of the A13 Wireless Charger. The DAC output changes from 1V to 3.3V which in turn changes the output voltage from 10V to 1V (on the fly) as needed by the algorithm of A13 wireless charger’s transmitter. This design utilizes best in Class Synchronous four Switch Buck Boost Controller LM5175. The design accepts an input voltage of 7Vin to 20Vin and provides the output of 1V- 10V@5 A. Output current never exceeds 5A to protect the charging Coil. The average current regulation loop of the IC at the output is used for this protection.
PMP10507 LM5175 Four Switch Buck Boost Variable Input, Variable Output Design | TI.com
PMP10507: PMP10507 is configured for 35Vin and was tested at a range of 17 to 54Vout. This design utilizes the LM5175, which is a wide VIN range Single Inductor, four switch synchronous Buck-Boost controller. This design is capable of regulating the output while the input is at, above or below the output. The switching frequency is set to 200 kHz. This Design is optimized for a regulated input of 35V and the output is adjusted from 17V to 54V out for a Pout max of 170W. The output voltage was adjusted by changing the bottom feedback resistor.
PMP20410 Variable Outputs Single Cell Battery 80W E-Cigarette Buck Boost Reference Design | TI.com
PMP20410: PMP20410 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for E-Cigarette applications. The output voltage can be selected from 1V to 10V at 13A to 28A using a trim resistor at the FB pin with a 0.2V to 3.1V bias voltage. This design also uses a non-sync boost regulator LMR62014 to provide the bias power for LM5175 which enables 2.7V input operation. The LM5175 pulse-by-pulse current limiting is inherent in the current-mode controller. The board includes enable, synchronization and power good functions. This design supports resistive heating element ranging from 0.1Ω to 0.5Ω to provide 80W power.
PMP10726 Programmable Output 50W 5-20Vout Buck-Boost USB Type-C Car Charger Adapter Reference Design | TI.com
PMP10726: PMP10726 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB Type-C car charger adapter applications. The output voltage can be selected for 5V, 9V, 15V, or 20V with a maximum output power of 50W by using I2C to adjust the TPL0401A-10 digital potentiometer. This design also uses the TPS70933 LDO to power the digital potentiometer. The LM5175 average current loop sets a maximum output current of 6.25A. Additional pulse-by-pulse current limiting is inherent in the current-mode controller.
PMP9495 Battery Charger and LED Driver - High Efficiency Synchronous 4 Switch Buck-Boost Topology | TI.com
PMP9495: PMP9495 is a 72 W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts a very Wide input voltage of 6Vin to 33Vin and provides the outputs of 13.4V@5 A for Constant Voltage Output Application, 9V-13.4V @ 5.5A for CC/CV Battery Charger application, and 5.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters.
16.8V/18A 4 Switch Buck Boost Reference Design
PMP10214: The PMP10214 reference design has a wide input voltage range from 8 -16V DC with a surge capapbility to 40V. The topology is 4 switch buck boost. It is best suited for charging 4s Li-Ion starter batteries (4 cells).
PMP20430 10V to 32Vin 25Vout at 1A Factory Automation I/O Module Reference Design | TI.com
PMP20430: PMP20430 is a 4-switch buck-boost controller utilizing the LM5175 for industrial applications. This design has a minimum operating input voltage of 10V and a maximum input voltage of 32V, supports 25Vout @ 1A. Switching frequency is set to 600kHz, during buck-boost mode, switching frequency drops in half, the buck and boost switches at 300kHz alternately with respected max and min duty cycle.
Battery Charger and LED Driver - High Efficiency Synchronous 4 Switch Buck-Boost Topology
PMP9495: PMP9495 is a 72 W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts a very Wide input voltage of 6Vin to 33Vin and provides the outputs of 13.4V@5 A for Constant Voltage Output Application, 9V-13.4V @ 5.5A for CC/CV Battery Charger application, and 5.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters.
PMP20042 4-Output USB Type-C 100W Buck Boost Reference Design | TI.com
PMP20042: PMP20042 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB Type-C™ applications. The output voltage can be selected for 5V, 9V, 15V or 20V at 5A using jumpers or open drain control switches. Additional pulse-by-pulse current limiting is inherent in the current-mode controller. The board includes enable, synchronization and power good functions.
PMP20327 Variable Outputs 2-Cell Battery 200W E-Cigarette Buck Boost Reference Design | TI.com
PMP20327: PMP20327 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for E-Cigarette applications. The output voltage can be selected from 1V to 10V at 20A to 45A using a trim resistor at the FB pin with a 0.2V to 3.1V bias voltage. This design also uses a non-sync boost regulator LMR62014 to provide the bias power for LM5175 during low Vin operation. The LM5175 pulse-by-pulse current limiting is inherent in the current-mode controller. The board includes enable, synchronization and power good functions. This design supports resistive heating element ranging from 0.1Ω to 0.5Ω to support various 200W operating conditions.
PMP40001 USB Type-C PD DFP 5/12/20V3A Output with 2~3 Cell Battery Input Power Bank Reference Design | TI.com
PMP40001: PMP40001 is a full featured USB type-C PD DFP reference design. The pure analog configuration for the USB type-C source controller--TPS25740 makes the PD negotiation easy. It supports 3 sets of output voltage options including 5V/12V/20V. The max output current is 3A which provides a maximal 60W output power @20Vo. This design's total efficiency can achieve 96% at full load by adopting the high performance buck-boost controller--LM5175, which also means a good thermal performance. The valid input voltage range is from 6V to 13.5V which is compatible with the 2S and 3S lithium battery pack.
LM5175 Four Switch Buck Boost Variable Input, Variable Output Design
PMP10507: PMP10507 is configured for 35Vin and was tested at a range of 17 to 54Vout. This design utilizes the LM5175, which is a wide VIN range Single Inductor, four switch synchronous Buck-Boost controller. This design is capable of regulating the output while the input is at, above or below the output. The switching frequency is set to 200 kHz. This Design is optimized for a regulated input of 35V and the output is adjusted from 17V to 54V out for a Pout max of 170W. The output voltage was adjusted by changing the bottom feedback resistor.
PMP9490 220W Synchronous 4 Switch Buck-Boost Converter | TI.com
PMP9490: PMP9490 is a 225W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts an input voltage of 9.5Vin to 20Vin and provides the outputs of 15V@15 A for Constant Voltage Output Application such as Voltage stabilizer or as Power amplifier SMPS, 10.8V to 15V@12.5A for CC/CV Battery Charger application, and 12.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters. The average current regulation loop of the IC at the output is used for Battery Charging profiling with no external circuit being involved.
