无法从文档中提取型号,请重试

Update your browser

Your browser (Internet Explorer) is out of date.

Update your browser for more security, comfort and the best experience for this site.

首页 > 元器件选型 > 放大器电路 > 比较器

TLV3201AIDCKT

加入BOM

TLV3201AIDCKT
已加入BOM:

Texas Instruments

5.5-V, high-speed, single push-pull comparator 5-SC70 -40 to 125

市场均价:
¥15.2674
市场总库存:
1
生命周期状态: Active
技术详情
价格 & 库存
替代料

CAD 模型信息

模型信息提供方: Samacsys
  • Part Symbol
  • Footprint
  • 3D Model
可下载的格式
  • Allegro
  • Altium
  • Cadence
  • CADSTAR
  • Circuit Studio
  • CR-5000
  • CR-8000
  • DesignSpark
  • DesignSpark PCB PRO
  • DipTrace
  • xDX Designer
  • Eagle
  • EasyEDA
  • Easy-PC
  • eCADSTAR
  • KiCad
  • Mentor
  • OrCAD
  • PADS
  • Proteus
  • Pulsonix
  • Quadcept
  • SOLIDWORKS PCB
  • TARGET 3001!
  • Zuken
  • 下载 CAD 档案

    从 Samacsys 下载 CAD 模型,即表示您同意我们的条款和隐私政策

    参考设计

    (7)
    TIPD144 Comparator with Hysteresis Reference Design | TI.com
    TIPD144: This TI Verified Design implements a comparator with hysteresis. Comparators are used to differentiate between two different signal levels. For example, a comparator may differentiate between an over temperature and normal temperature condition. Noise or signal variation at the comparison threshold will cause multiple transitions. Hysteresis sets an upper and lower threshold to eliminate the multiple transitions caused by noise.
    TIPD130 Dual Polarity High-Voltage Differential Input Interface for Low-Voltage Comparators Reference Design | TI.com
    TIPD130: This TI Verified Design provides the theory, component selection, simulation, schematic, PCB layout, BOM, and measured performance for a dual polarity (bipolar), high-voltage differential input interface for low-voltage comparators. The design allows a comparator such as the TLV3201 to operate with a single +3.3 V supply and to compare two input voltages that not only exceed its normal input range, but can be of either (±) polarity. The design takes into account all the comparator and passive component errors and results in <10 mV, of dc input error. Worst-case analyses techniques are provided to determine the dc error contributed by limited resistor tolerance, for the resistors used in the comparator input networks.
    Comparator with Hysteresis Reference Design
    TIPD144: This TI Verified Design implements a comparator with hysteresis. Comparators are used to differentiate between two different signal levels. For example, a comparator may differentiate between an over temperature and normal temperature condition. Noise or signal variation at the comparison threshold will cause multiple transitions. Hysteresis sets an upper and lower threshold to eliminate the multiple transitions caused by noise.
    TIDA-00448 Flexible High Current IGBT Gate Driver with Reinforced Digital Isolator Reference Design | TI.com
    TIDA-00448: The TIDA-00448 reference design is an isolated IGBT gate driver with bipolar gate voltages intended for driving high power IGBT’s requiring high peak gate current up to 40 A. TI’s NexFET power blocks which scales in this range, with same package, enables single design to be used for multiple drive platforms with different power ratings. A Digital isolator is used to achieve reinforced isolation with transient surge rating of 8kV and 50kV CMTI. The design incorporates DESAT protection using a fast transient response comparator. The DESAT detection threshold and the soft turn-off time are configurable. The design can interface with PWMs from 3.3 V and 5 V MCUs along with fault, reset and UVLO feedbacks.
    Dual Polarity High-Voltage Differential Input Interface for Low-Voltage Comparators Reference Design
    TIPD130: This TI Verified Design provides the theory, component selection, simulation, schematic, PCB layout, BOM, and measured performance for a dual polarity (bipolar), high-voltage differential input interface for low-voltage comparators. The design allows a comparator such as the TLV3201 to operate with a single +3.3 V supply and to compare two input voltages that not only exceed its normal input range, but can be of either (±) polarity. The design takes into account all the comparator and passive component errors and results in <10 mV, of dc input error. Worst-case analyses techniques are provided to determine the dc error contributed by limited resistor tolerance, for the resistors used in the comparator input networks.
    TIDA-00929 Spectrum Analyzer Signal Conditioning and Processing for Capturing Arc Signatures Reference Design | TI.com
    TIDA-00929: The TIDA-00929 TI design demonstrates bandwidth optimized analog front end (AFE) and real-time FIR implementation using low power to capture broadband frequency spectrum in any waveform. Operational amplifier in each signal path is chosen based on the gain, signal bandwidth, low noise, close to the rail swing requirements while consuming low power. The waveform is processed in real-time both in frequency and time domain using mixed signal ultra low power microprocessor with built in vector math engine.
    Flexible High Current IGBT Gate Driver with Reinforced Digital Isolator Reference Design
    TIDA-00448: The TIDA-00448 reference design is an isolated IGBT gate driver with bipolar gate voltages intended for driving high power IGBT’s requiring high peak gate current up to 40 A. TI’s NexFET power blocks which scales in this range, with same package, enables single design to be used for multiple drive platforms with different power ratings. A Digital isolator is used to achieve reinforced isolation with transient surge rating of 8kV and 50kV CMTI. The design incorporates DESAT protection using a fast transient response comparator. The DESAT detection threshold and the soft turn-off time are configurable. The design can interface with PWMs from 3.3 V and 5 V MCUs along with fault, reset and UVLO feedbacks.
    显示更多价格 & 库存吗?

    市场价格分析

    没有可用的数据

    价格走势

    库存走势

    显示更多替代料吗?
    新建BOM