更多产品参数
Zener Diode, TO-236AA, MICRO MINIATURE PACKAGE-3
制造商:
ON Semiconductor
制造商型号:
BZX84C5V1
符合标准:
Rohs 不符合
数据手册:
文档下载
BZX84C5V1数据表
参考设计(35)
18Vdc-60Vdc Input, 3.3V @ 30A Output, 93% Efficient Active Clamp Forward
PMP8252: The PMP8252 reference design provides 3.3V at 30A from a wide range 18V-60V telecom input with a peak efficiency that is greater than 93%. This design uses the UCC2897A active clamp controller along with Texas Instruments' NexFET power MOSFETs for synchronous rectification.
36V-72V Input 5V/20A 95% Efficient Active Clamp Forward; 1/4 Brick
PMP5364: The PMP5364 reference design provides 5V at 20A (100W) from a standard 48V telecom input with up to 95% efficiency. This design uses the UCC2897A active clamp controller along with TI NexFET synchronous rectifiers. The low Rdson of the CSD17301Q5A reduces conduction losses and die area of the synchronous rectifiers. The circuit is built in an industry standard 1/4 brick footprint.
100VAC-265VAC 100W High Bay LED Lighting (80V @ 350mA)
PMP4862.2: The PMP4862 reference design drives three separate LED strings (up to 77V) at 350mA from a universal AC input. The UCC28810 is used in a PFC-Flyback configuration to provide power factor correction and isolation at the same time. Each LED driver uses one TPS40210 to control the individual LED current. PWM dimming, ON/OFF control, current monitoring, and a trim function are all provided for each individual LED string. The PFC-flyback is over 87% efficient, while the buck LED drivers are over 92% efficient. The overall efficiency is over 80%.
Universal AC DLP Power Supply (10V @ 6A) - PMP5500.2 - TI Tool Folder
PMP5500: This reference design provides 400W of power from a universal AC input with power factor correction. The UCC28019A controls a PFC boost front end, while the UCC25600 LLC resonant-half bridge converts the PFC output to isolated 40V, 33V, and 27V outputs. The total system efficiency is over 89% with a 230VAC input and over 85% with an 115VAC input.
48V Input 3.3V/30A with Output Pre-bias
PMP5997: This reference design generates a 3.3V/100W output from a standard 48V telecom input and allows for a pre-biased output. The UCC2897A controls operation of the active clamp power stage. The drive signal for the synchronous rectifiers is sent to the secondary side through an ISO7220 digital isolator. This drive signal is blanked out during startup to allow for a pre-biased output. This design achieves efficiencies over 92% and is built on a standard ¼ brick footprint.
Universal AC DLP Power Supply (10V @ 6A)
PMP5500.2: This reference design provides 400W of power from a universal AC input with power factor correction. The UCC28019A controls a PFC boost front end, while the UCC25600 LLC resonant-half bridge converts the PFC output to isolated 40V, 33V, and 27V outputs. The total system efficiency is over 89% with a 230VAC input and over 85% with an 115VAC input.
8VDC-16VDC 7.6V/700mA LED Driver
PMP4937: This reference design drives two series connected white LEDs at 700mA. The steady-state input range is 8VDC to 16VDC, but the circuit is designed to survive a 52VDC input transient condition. The TPS40211 boost controller is used in an "upside-down" buck topology for a simple, low-cost solution. This circuit includes enable, PWM dimming, current trimming, and a current sense functions for interfacing with an external microprocessor.
36Vdc-75Vdc Input, 5V @ 25A Output, 94% Efficient Active Clamp Forward
PMP5753: The PMP5753 reference design provides 5V at 125W from a standard 48V telecom input with greater than 94% efficiency. This design uses the UCC2897A active clamp controller along with self-driven synchronous rectifiers. Texas Instruments NexFET technology is used for the synchronous rectifiers, improving the efficiency by nearly 2% over conventional MOSFETs. The output voltage can be adjusted up to 7V.
Flyback Converter (24V @ 3A) PoE Powered Device (PD)
PMP7279: The PMP7279 reference design provides 24V at 72W (3A) from a wide ranging 18VDC to 57VDC input with 92% efficiency. This design uses the TPS40210 to control a diode rectified flyback converter for a low cost and efficient design.
Universal LED driver
PMP2587: Universal DC/DC LED driver (buck) with dimming pulse generator for three LEDs up to 700mA
12Vdc-52Vdc Input, 12V @ 250mA Output, Isolated Flyback
PMP4218: The PMP4218 reference design uses the TPS40210 to generate a 12V/0.25A output from either a 24VAC or 12Vdc-52Vdc input. This design achieves over 80% efficiency and uses 100% surface mount parts. This circuit consumes less than 2 square inches on a single-sided, two layer, PCB layout.
SEPIC (13.5 - 18.0V @ 1.2A) for LED Drivers
PMP4729: PMP4729 is a wide input voltage range (8024V) LED driver for automotive application. It supplies a string of 3-4 LEDs (13.5 .. 18V) with a current of 1.2A. The converter with TPS40211 is in sepic configuration, has a dimming input (100..200 Hz PWM) and additional circuitry for input protection (transient protection, active reverse polarity protection).
18Vdc-57Vdc Input Isolated Battery Charger 29V @ 3A
PMP4963: The PMP4963 reference design uses the TPS40210 PWM controller in a flyback configuration to supply 3A of charge current at over 90% efficiency. The output voltage is limited by the control circuitry to 29.4V.
80V dc Input, 2-Channel, 350mA LED Driver (10V to 60V String)
PMP4154: This reference design contains two duplicate LED drivers. Each circuit drives a 10V to 60V series connected string of LEDs at 350mA. The input range is 70VDC to 90VDC. The TPS40210 boost controller is used in an "upside-down" buck topology for a simple, low-cost solution. This circuit includes an enable, PWM dimming, current trimming, and a current sense functions for interfacing with an external microprocessor.
100VAC-265VAC 100W High Bay LED Lighting (80V @ 350mA)
PMP4862.4: The PMP4862 reference design drives three separate LED strings (up to 77V) at 350mA from a universal AC input. The UCC28810 is used in a PFC-Flyback configuration to provide power factor correction and isolation at the same time. Each LED driver uses one TPS40210 to control the individual LED current. PWM dimming, ON/OFF control, current monitoring, and a trim function are all provided for each individual LED string. The PFC-flyback is over 87% efficient, while the buck LED drivers are over 92% efficient. The overall efficiency is over 80%.
100VAC-265VAC 100W High Bay LED Lighting (100V @ 1.2A)
PMP4862.1: The PMP4862 reference design drives three separate LED strings (up to 77V) at 350mA from a universal AC input. The UCC28810 is used in a PFC-Flyback configuration to provide power factor correction and isolation at the same time. Each LED driver uses one TPS40210 to control the individual LED current. PWM dimming, ON/OFF control, current monitoring, and a trim function are all provided for each individual LED string. The PFC-flyback is over 87% efficient, while the buck LED drivers are over 92% efficient. The overall efficiency is over 80%.
"18V-36V Input 6V/100W 95% Efficient Active Clamp Forward
PMP6942: The PMP6942 reference design provides 6V at 100W (17A) from a standard 24V telecom input with greater than 94% efficiency. This design uses the UCC2897A active clamp controller along with the TI CSD17312Q5 NexFET synchronous rectifier.
17V to 36Vin Isolated Flyback 53V @ 70W
PMP5651: This DC/DC converter is an isolated Flyback delivering 53V @ 1.35A from 17V to 36V input voltage. A supplementary overvoltage protection with a further optocoupler has been implemented.
Isolated DM Flyback 6.5V@1A
PMP6606: This low-cost (6.5W) isolated synchronous discontinuous flyback regulator produces a 6.5V output from a low-voltage (18V – 36V) input. A full-load efficiency of nearly 90% was achieved from a 24V nominal input.
Isolated Flyback that generates - 48 Vin, 20Vout at 3A
PMP4696: 60W isolated telecom flyback, 20V @3A
18V-36V Input 5V/15A; 94% Efficient Active Clamp
PMP5117: The PMP5117 reference design provides an isolated 5V at 15A from a 18V to 36V input range. This design uses the UCC2897A active clamp controller along with Texas Instruments' NexFET technology, CSD16321Q5, synchronous rectifiers to achieve up to 94% efficiency.
400VDCin, 12V@460W, LLC with Synchronous Rectifiers
PMP5967: The PMP5967 reference design provides a 12V/38A output with over 94% efficiency from a 380VDC input. This design uses the UCC25600 to control the resonant LLC converter. The UCC24610 synchronous rectifier controller is used to control two banks of CSD18501Q5A MOSFETs, eliminating the need for heat sinks on the output rectifiers.
36VDC-72VDC Input, 5V/36A Interleaved Active Clamp Forward
PMP4016: This reference design generates a 5V/36A output from a standard 48V telecom input. Two UCC2891controllers are configured to control two interleaved active-clamp forward power stages. The secondary circuitry implements self-driven synchronous rectifiers for a highly efficient design. Splitting the power into two paralleled power stages reduces conduction losses and allows this design to achieve efficiencies greater than 94 percent.
100VAC-265VAC 100W High Bay LED Lighting (80V @ 350mA)
PMP4862.3: The PMP4862 reference design drives three separate LED strings (up to 77V) at 350mA from a universal AC input. The UCC28810 is used in a PFC-Flyback configuration to provide power factor correction and isolation at the same time. Each LED driver uses one TPS40210 to control the individual LED current. PWM dimming, ON/OFF control, current monitoring, and a trim function are all provided for each individual LED string. The PFC-flyback is over 87% efficient, while the buck LED drivers are over 92% efficient. The overall efficiency is over 80%.
50Vdc-60Vdc Input, 2-Channel, 350mA LED Driver (10V to 40V String)
PMP4936: This reference design contains two duplicate LED drivers. Each circuit drives a 10V to 40V series connected string of LEDs at 350mA. The input range is 50VDC to 60VDC. The TPS40210 boost controller is used in an "upside-down" buck topology for a simple, low-cost solution. This circuit includes synchronization, enable, PWM dimming, current trimming, and a current sense functions for interfacing with an external microprocessor.
36VDC-72VDC Input, 5V/60A Interleaved Active Clamp Forward
PMP2214: This reference design generates a 5V/60A output from a standard 48V telecom input. Two UCC2891controllers are configured to control two interleaved active-clamp forward power stages. The secondary circuitry implements self-driven synchronous rectifiers for a highly efficient design. This design includes trimming, remote sense, and output overvoltage features.
18Vdc-60Vdc Input, 3.3V @ 25A Output, 94% Efficient Active Clamp Forward
PMP6753: The PMP6753 reference design provides 3.3V at 25A from a wide range 18V-60V telecom input with greater than 94% efficiency. This design uses the UCC2897A active clamp controller along with Texas Instruments' NexFET power MOSFETs for synchronous rectification.
PFC Boost with Transition Mode Buck 312V@80mA
PMP5682: A transition mode (TM) Boost PFC and a TM Buck deliver from high line a clean 80mA current to a LED string, max. voltage 312V. The PCB board has been developed to fit into a T8 fluorescent tube, suitable for retrofit purpose. A PWM dimming input is also included.
288-450Vdc Input, 7V/12V/15V Output at 16W, QR Flyback
PMP4794: The PMP4794 reference design uses the UCC28600 green mode flyback controller to generate three outputs (7V, 12V, and 15V). The 7V and 12V outputs are isolated, while the 15V is non-isolated. The 12V output is regulated. This supply is 84% effficient at maximum load, and consumes less than 100mW at no load.
LED Driver with 730mA @ 16 .. 32V and 9 .. 19V input voltage range
PMP5748: This design is a LED driver providing an ouput current of 730mA within an voltage range of 16-32V. The input voltage range is 9-19V.
55Vdc-80Vdc Input, 2-Channel, 350mA LED Driver (10V to 50V String)
PMP4791: This reference design contains two duplicate LED drivers. Each circuit drives a 10V to 50V series connected string of LEDs at 350mA. The input range is 55VDC to 75VDC. The TPS40210 boost controller is used in an "upside-down" buck topology for a simple, low-cost solution. This circuit includes an enable, PWM dimming, current trimming, and a current sense functions for interfacing with an external microprocessor.
PFC, Resonant Half-Bridge, Buck (PFC, 42V@6A) for Digital Audio
PMP5327: The PMP5327 reference design provides a 42V/6A output with power factor correction from a universal AC input voltage range. This design uses the UCC28019A to control the front end PFC boost stage. The output of the PFC is followed by a UCC25600 LLC resonant half-bridge. The total efficieny, from input to output is over 92% from a 230VAC input and over 89% from a 115VAC input. An additional 12V/250mA output is also generated by this supply.
Universal AC DLP Power Supply (40V @ 10A)
PMP5500.1: This reference design provides 400W of power from a universal AC input with power factor correction. The UCC28019A controls a PFC boost front end, while the UCC25600 LLC resonant-half bridge converts the PFC output to isolated 40V, 33V, and 27V outputs. The total system efficiency is over 89% with a 230VAC input and over 85% with an 115VAC input.
18V-36V Input 28V/100W Flyback
PMP6943: The PMP6943 reference design provides 28V at 100W (3.6A) from a standard 24V telecom input with greater than 92% efficiency. This design uses the TPS40210 to control a diode rectified flyback converter for a low cost and efficient design.
Rochester Electronics
分销商编号：
未知
交货地:
港台地区
单价:
- 阶梯 人民币价格(含税) 美元价格
- 100+ - $0.0336
- 500+ - $0.0302
- 1000+ - $0.0278
- 10000+ - $0.0249
- 100000+ - $0.0208
请输入数量：
-+
总计:
库存/包装：
3
起订量：
100
递增量：
100
搜索更多的分销商结果
搜索
请输入完整或部分产品型号，最少 3 个字母或数字
