更多产品参数
Res Thick Film 0603 200K Ohm 1% 1/10W ±100ppm/C Molded SMD Paper T/R
制造商:
Vishay
制造商型号:
CRCW0603200KFKEA
符合标准:
不含铅
数据手册:
文档下载
CRCW0603200KFKEA数据表
参考设计(32)
System Level Power Reference Design for A13 Automotive Wireless Charger Transmitter
PMP10709: PMP10709 is a system optimized 50 W power designs for A13 Wireless Charger Transmitter used in automotive system. The design has various front end automotive protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Through PFET’s body diode), Battery Disconnect Switch with OVP protection (PFET). PMP10709 is primarily four Switch synchronous Buck – Boost design, which supports wide Input voltage range (7V-20V) and delivers any output from 1V-10V based on DAC output of the A13 Wireless Charger. The DAC output changes from 1V to 3.3V which in turn changes the output voltage from 10V to 1V (on the fly) as needed by the algorithm of A13 wireless charger’s transmitter. This design utilizes best in Class Synchronous four Switch Buck Boost Controller LM5175. The design accepts an input voltage of 7Vin to 20Vin and provides the output of 1V- 10V@5 A. Output current never exceeds 5A to protect the charging Coil. The average current regulation loop of the IC at the output is used for this protection.
Automotive Power Supply with Pre-Boost Reference Design
PMP10223.1: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Class 1 Non-isolated Buck Converter (5V/560mA) for PoE PD Applications Reference Design
PMP9676: This converter is used for Class 1 PoE PD applications where isolation is not required. The TPS2378 PD controller plus LM5006 buck converter provide 5V/560mA with good efficieny in a small size. The LM5006 can be configured with a diode rectifier for lowest cost or a synchronous FET rectifier for improved efficiency.
High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top
TIDA-00510.1: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC. This results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
Isolated Flyback Converter for Industrial Bias Supply - Reference Design
PMP7932: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
LM3447 - 230VAC, 10W, Phase Dimmable Non-isolated Buck-Boost PFC LED Driver
PMP8025: The main purpose of this reference design is to demonstrate a high performance offline phase dimmable Buck-Boost PFC LED driver based on LM3447. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows:
Wide Input Voltage Range Automotive Cuk LED Driver Reference Design (35V @ 0.75A)
PMP6012: PMP6012 reference design presents the TPS92690Q1 DC-DC controller driving a 18V to 35V string of LEDs at 750mA of current in a Cuk configuration. The Cuk topology features continuous input and output currents which helps reduce EMI and also allows one end of the LED string to connect to common ground allowing for a single wire system.
High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top
TIDA-00510: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC and results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
Dual-Channel Full-Bridge Converter (54V @ 30A) for PoE Power Sourcing (PSE)
PMP6712: PMP6712 is a phase-shifted full-bridge converter capable of delivering 1600W of isolated output power and achieving efficiency of greater than 96%. This design uses the UCC28950 controller in a dual phase master-slave configuration. An LM5017 constant on-time synchronous buck regulator provides bias power to primary and secondary-side circuits using a coupled inductor with isolated flyback winding. The isolation voltage is specified as 2250VDC, allowing this design to be used as a system supply for Power Over Ethernet and other telecommunications applications.
3.3V Low-Cost Non-Isolated Offline Converter for Smart E-Meters Reference Design
PMP9310: The PMP9310 is an offline converter that supplies 3.3VDC output at up to 132mA. It is used for 50Hz single-phase smart e-meters where maximum allowable input apparent power is regulated (typically 4VA) and galvanic isolation is unnecessary. It solves the problem of limited available output power typically seen in a linearly regulated output stage. By employing the wide input LM5017 buck switcher, the capacitor-drop design sets the input of the DC-DC stage at a high value of 72V and extracts significantly more power from the mains at a given input apparent power. The extra available output power supports a system design that incorporates extra functionalities.
Automotive Power Supply with Pre-Boost Reference Design
PMP10223.4: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Automotive Power Supply with Pre-Boost Reference Design - PMP10223.2 - TI Tool Folder
PMP10223: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Automotive Power Supply with Pre-Boost Reference Design
PMP10223.2: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Wide Bandwidth Optical Front-end Reference Design
TIDA-00725: This reference design implements and measures a complete 120MHz wide bandwidth optical front end comprising a high speed transimpedance amplifier, fully differential amplifier, and high speed 14-bit 160MSPS ADC with JESD204B interface. Hardware and software are provided to evaluate the performance of the system in response to high speed optical pulses generated from the included laser driver and diode for applications including optical time domain reflectrometry (OTDR).
Non-Standard (>25.5W) PoE - High Efficiency Forward Converter (5V@10A) Reference Design
PMP8923: This converter provides a high power PoE output of 5V/10A. The TPS2379 PD controller allows the use of an external hot swap FET for increased efficiency. The UCC2897A PWM controller is used to implement a high efficiency active clamp forward converter.
4.5Vin to 5.5Vin; 4Vout @ 0.7A; Flyback
PMP7964: A Flyback design accepting an input voltage of 4.5Vin to 5.5Vin and providing an isolated output of 4Vout that can deliver 0.7A.
High Power Density 12Vin, 12.6W Buck Converter with Integrated Inductor
TIDA-00471: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area and results in >86% efficiency with only 1.8W of power loss and 6mV of output voltage ripple requiring only 5x100uF ceramic output caps.
200W Natural Interleaving Transition-Mode PFC Flyback LED Driver Reference Design
PMP10116: This design uses the UCC28063A transition-mode pfc controller to drive LEDs up to 700mA current from an AC input. This flyback pfc topology provides isolation and uses quasi-resonant mode control. It supports analog dimming on the output side.
Shunt based Ground Fault Protection for Inverters Powered from 220Vac Supply Reference Design
TIDA-00442: The TIDA-00442 TI design provides a reference solution for detecting ground fault in inverter based drives. Inverter current is measured on both DC positive and DC negative bus using shunt resistors. Current on DC positive bus is measured using INA170 which is powered by low side switched buck converter. Current on DC negative bus is sensed using precision opamp’s. The difference between the two measured currents is compared against a fixed threshold to determine the ground fault condition using high speed comparators.
Isolated Flyback Converter for Industrial Bias Supply - Reference Design
PMP7932.1: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
Forward converter with Universal input driving 2x6 LEDs
PMP7762: PMP7762 is an offline LED driver with TRIAC dimming. It has short circuit protection as well as op amp control for dimming. It uses 2 op amp control for each LED string to ensure that current in the LED strings match. LM3445 includes a bleeder circuit to ensure proper triac operation by allowing current flow while the line voltage is low to enable proper firing of the triac.
150W Boost Converter with LM5121 Reference Design
PMP8673: The PMP8673 reference design is a synchronous boost converter optimized for high efficiency while maintaining a small form factor. This reference design has a voltage input range of 34.5-37.5V (35V nominal) and provides an output voltage of 55.5V. The synchronous boost topology enables efficiencies greater than 97% in the 2-3A load range. The switching frequency is set for 400Khz allowing the use of smaller external components and a total board area of less than 60 square centimeters.
Automotive Power Supply with Pre-Boost Reference Design
PMP10223.5: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Cap-Drop Offline Power Supply for Standard-Compliant Feature-Rich E-Meters Reference Design
PMP9311: The PMP9311 is a low power capacitor-drop type of offline converter that takes a 50Hz AC input of 85V to 230V and puts out a regulated DC 3.3V at up to 85mA. It is used for electronic electricity meters where apparent power consumption is regulated and galvanic isolation is not required. The high output current capability for the same input apparent power limit supports a feature-rich electricity meter design. The increased output power is achieved by allowing the clamped zener voltage to be as high as 42V, and the employment of a wide input range buck switching regulator.
38V@2A Synchronous Boost Reference Design
PMP10324: The PMP10324 sync-boost reference design provides 38V @ 2A over a wide input range covering the 24V rail. It uses dual external FETs to achieve a full load efficiency of 97% at 24Vin. This design uses minimal footprint parts with all ceramic capacitors.
Single LED with High Current 20A Application using TPS92641
PMP8016: The main purpose of this reference design is to demonstrate a high performance, high current and easy to use, synchronous buck LED driver based on TPS92641. This LED driver is designed for application with using high power single LED within 20A.The operating conditions and performance of the reference design are as follows:
14V-24Vdc Input Voltage, 3-series Cell Li-Ion Battery Charger Reference Design
PMP10921: The PMP10921 reference design uses the BQ24600 Li-Ion synchronous buck controller to charge up to three series cells. It is designed to charge the cells at 0.372A, but can charge at higher currents by changing one resistor. The board area is less than 20mm x 20mm.
100-240VAC Input, 60W, 2-string, PWM Dimmable LED Driver Reference Design
PMP6024: PMP6024 is an offline, LED driver circuit consisting of an isolated, power-factor corrected, constant output voltage flyback converter followed by two DC/DC buck LED current controllers. It is suitable for indoor or outdoor area lighting applications of 3500-5000 lumens (depending upon LED selection). LED brightness is controlled by a 3.3V, 10kHz PWM signal which is converted to a DC level adjustment of the LED string currents avoiding PWM modulation of the light output.
Boost Converter With 18 to 30Vin and 300V @ 10mA Output Reference Design
PMP8621: This design is a boost converter generating 300V @ 10mA from an input voltage range of 18 to 30V.
Automotive Power Supply with Pre-Boost Reference Design - PMP10223.4 - TI Tool Folder
PMP10223: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Low-Cost Digitally Programmable Gain Amplifier Reference Design
TIPD204: This simple and low-cost digitally programmable gain amplifier design creates non-inverting gains ranging from 6dB (2V/V) to 60dB (1000V/V). The design is based on a general purpose op amp and a digital potentiometer as one of the gain-setting elements. The digital potentiometer is controlled with a standard I2C digital interface.
Automotive Power Supply with Pre-Boost Reference Design
PMP10223.3: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
Avnet Asia
分销商编号：
CRCW0603200KFKEA
单价:
暂无价格信息
请输入数量：
-+
库存/包装：
0
起订量：
5,000
递增量：
5,000
备货时间：
13 Weeks, 0 Days
